ALUMINIUM CANS WASTE MELTING IN MICROWAVE FIELD
DOI:
https://doi.org/10.24193/subbambientum.2019.2.06Keywords:
aluminium cans waste, microwave melting, toxic compounds, thermal filter.Abstract
Recycling of aluminium, particularly aluminium beverage cans is important due to several economic and environmental reasons. Aluminium beverage cans are by far the most recycled consumer beverage packages globally, by units, weight and percentage recycled. It amounts to more than twice the recycling rate and recycled content percentages for beverage packages of other materials. Recycling of aluminium requires only 5-10% of the energy for primary aluminium production. In this paper, the melting of cans wastes in microwave furnace as well as the treatment of noxious emissions in a microwave thermal filter has been preliminary investigated. Melting temperature, composition of the melting - protection fluxes as well as waste/flux ratio on the metal recovery efficiency have been investigated. During the cans waste melting, due to the burning of paint and lacquer coatings, environmental toxic compounds such as: volatile organic compounds (VOCs) (acetone, benzene, ethylbenzene, styrene, toluene, etc.) have been detected in the effluent gases. The treatment was carried out by passing the gases through a microwave susceptor granular material filter (SiC balls), placed in a microwave transparent tube. It was observed that the temperature of the filter has a major influence on the neutralization of the toxic compounds, the content in the gases being reduced below the legal limits.References
Appleton T.J., Colder R.I., Kingman S.W., Lowndes I.S., Read A.G., 2005, Microwave technology for energy-efficient processing of waste. Applied Energy, 81, pp. 85–113.
Capuzzi S., Timelli G., 2018, Preparation and Melting of Scrap in Aluminium Recycling: A Review. Metals, 8 (249), p. 1-24
Chandrasekaran S., Basak T., Ramanathan S., 2011, Experimental and theoretical investigation on microwave melting of metals. J. of Materials Processing Technology, 211, p. 482–487.
Das S., Hughes M., 2006, Improving aluminium can recycling rates: A six sigma study in Kentucky. JOM: the journal of the Minerals, Metals & Materials Society, 58 (8), pp. 27-31, DOI: 10.1007/s11837-006-0049-1.
Gupta M., Wong W.L.E., 2007, Microwaves and Metals, Singapore, 228 p., doi:10.1002/9780470822746
Liu G., Muller D.B., 2012, Addressing Sustainability in The Aluminium Industry: A Critical Review of Life Cycle Assessment. J. Clean. Prod., 35, p. 108-117.
Sun X., Hwang J.-Y., Huang X., Li B., Shi S., 2005, Effects of microwave on molten metals with low melting temperatures. Journal of Minerals & Materials Characterization & Engineering, 4 (2), pp. 107-112.
Van der Harst E., Potting J., Kroeze C., 2016, Comparison of different methods to include recycling in LCAs of aluminium cans and disposable polystyrene cups. Waste Manag, 48, pp. 565-583, doi: 10.1016/j.wasman.2015.09.027.
Verran G., Kurzawa U., 2008, An experimental study of aluminium can be recycling using fusion in induction furnace. Resources, Conservation and Recycling, 52 (5), pp. 731-736, doi: https://doi.org/10.1016/j.resconrec.2007.10.001.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2019 Studia Universitatis Babeș-Bolyai Ambientum
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.